TrustSEAL
Shree Laxmi Mild Steel Liquid Gas Fuel Thermic Fluid Heater, For Business Use
₹ 6,50,000
- Maximum Temperature: Upto 320 Degree Celsius
- Material: Mild Steel
- Usage/Application: Business Use
- Brand: Shree Laxmi
WhatsAppCall Now
- TrustSEAL
Transient Heater, Size: 800 Mm X 800 Mm X 800 Mm
₹ 2,25,000- Brand: MAC SYSTEMS
- Connecting: Flange End
- Shape: Round,Square
- Size: 800 mm x 800 mm x 800 mm
WhatsAppCall Now 
Stainless Steel THERMIC OIL AIR HEATER HEAT EXCHANGER
₹ 10,001- Material: Stainless Steel
- Usage/Application: Heat Exchanger
- Cooler Type: Air Cooled
- Fin Surface: Flat
WhatsAppCall Now
Stainless Steel Thermic Fluid Air Heater, For Sugar Industry
- Usage/Application: Sugar Industry
- Material: Stainless Steel
- Voltage V: 240 V
- Power: 3 kW
WhatsAppCall Now
Thermal Fluid Air Heater
Deals in supplying and exporting gas heaters that includes industrial gas fired heaters, gas fired thermic fluid heaters, vertical gas fired thermic fluid heaters and horizontal gas fired thermic fluid heaters etc.WhatsAppCall Now
Transient Heater
Transient HeaterWhatsAppCall Now
TRANSIENT HEATER
TRANSIENT HEATERWhatsAppCall Now
Transient Heater
Salient Features Compact Size. No pump required as massecuite heating by low temp vapours. Power saving. Totally maintenance free. In Sugar factory the massecuit going to the centrifugal machine ( C massecuit in particular) should be at a specific temperature so as to minimize its viscosity and to avoid overloading of centrifugal motor. Massecuit is cooled in crystallizer to extract maximum sugar from molasses but the disadvantage of cooling is, massecuit while cooling gets more viscous, sticky & does not flow freely up to the centrifugal machine. The machine also gets ununiformly overloaded, thus it s purging capacity reduces. To overcome all these problems there arises the need of a heater that raises the temperature of massecuit. The heater should fulfill following things.The heater design should be such that the massecuit gets heated quickly during its transit time from pug mill to centrifugal machine. If not then the problem of raise in molasses purity arises. The heater must have minimum retention time. The heater should be dimensionally small and compact so that it can be fitted above the centrifugal machine, below pug-mill. The most important is that the heater should have minimum maintenance.Heating media for the heater should be such that the co-efficient of heat transfer should be high so that the massecuit gets heated quickly during transit time through the heater. VISHWA Transient Heater fulfills all the above points so it can be really called as TRANSIENT HEATER . Heating media in all conventional Transient Heaters is hot water. The co-efficient of heat transfer from liquid (hot water) to semi solid i.e. massecuit is very less, but that of vapour to liquid is very high. Vapours when get condensed a large amount of Latent Heat is released. VISHWA Transient Heater is designed, based on this phenomenon. Working Principle Self-generated low temperature vapours are used as heating media in VISHWA Transient Heater. Input energy required to run the Heater is only about 20 Kgs. of 100 PSIG. steam per hour. Heat energy of steam is transferred to the distilled water (Condensate) filled in the part of heater called Vaporizer . Condensate in the vaporizer gets evaporated and vapours are produced. These vapours are used as heating media in the Transient Heater which circulate through S.S. tubes and get condensed again after letting out the latent heat to the massecuit. Condensate flows back in to the vaporizer and again vapours are produced. This is how massecuit heating continues in Transient Heater. The heating media loop is completely sealed and kept under vacuum to generate vapors at low temperature and heater becomes self regulating of maintenance free. Here regulating the steam supply to the vaporizer controls the vapour temperature. A simple ON / OFF type closed loop temperature control system is provided along with the Transient Heater.Get Best PriceCall Now- Exporter
magma Stainless Steel Thermic Fluid Air Heater, For Industrial
₹ 32,000- Size: can be customised
- Material: Stainless Steel
- Usage/Application: Industrial
- Brand: magma
84% Response RateWhatsAppCall Now - TrustSEAL
Mild Steel Thermic Fluid Heaters
₹ 4,00,000- Material: Stainless Steel, Mild Steel
- Temperature: 300 deg C
- Pressure: I to 3 bar
- Min Capacity: 1,00,000 Kcals/hr
94% Response RateWhatsAppCall Now - TrustSEAL
Mild Steel Thermic Fluid Heating System
₹ 3,00,000- Material: Mild Steel
- Maximum Temperature: Up to 300 degree C
- Usage/Application: Agriculture Industry, Food Industry, Chemical Industry, Etc
- Brand: Multitech
WhatsAppCall Now - TrustSEAL
Thermic Fluid Air Heaters
₹ 9,50,000- Material: Mild Steel
- Firing Mode: Auto/Manual
- Color: Grey & Offwhite
- Voltage V: 430
82% Response RateWhatsAppCall Now 
Thermic Fluid Air Heaters
₹ 30,000Thermic Fluid Air Heaters for heating air using thermic fluids like Shell Thermia, Marlotherm, Dowtherm and other petroleum oils as heating medium are manufactured using root soldered wire wound fin tubes. Our designs result in economical designs coupled with low air side pressure drops. Thermic fluid air heaters made by us are being used in dryers in coated paper industry, steel strip coating and finishing lines, chemical and dye dryers. Base tubes of carbon steels, stainless steel 304, stainless steel 316 and other stainless steel grades finned with galvanized mild steel, copper and stainless steel fins are used in fabrication of air heating exchangers. The body material used so far is carbon steel and stainless steels.WhatsAppCall Now
Transient Heater
Transient HeaterWhatsAppCall NowSeller Type
Available price ranges for Thermic Fluid Air Heaters
- Below ₹60,000
- ₹60,001 - ₹2,20,000
- ₹2,20,001 - ₹5,00,000
- Above ₹5,00,001
Transient Heater
Transient HeaterGet Best PriceCall Now