Panasonic PT-DS20K2 DLP Projector, 1400 × 1050 pixel

Screen Size

1.78 – 25.4 m (70 inch – 1000 inch )

Display Type

DLP Chip × 3 (R, G, B), DLP Projection System

Model Number

PT-DS20K2

Brand

Panasonic

Resolution

1400 × 1050 pixel (Input Signals That Exceed This Resolution Will Be Converted to 1400 × 1050 pixel)

Power supply

200 – 240 V AC, 12 A, 50/60 Hz (3-wire single-phase)

Power consumption

2,060 W (2,100 VA) (0.3 W with STANDBY MODE set to ECO. 1 9 W with STANDBY MODE set to NORMAL.), max. 7,031 BTU (without light output: 6,758 BTU )

DLP chip - Panel size

24.1 mm (0.95 inch) diagonal (4:3 aspect ratio)

DLP chip - Pixels

1,470,000 (1,400 × 1,050) × 3, total of 4,410,000 pixels

Lens

Optional powered zoom/focus lenses

Lamp

432 W UHM lamps (× 4) (four lamp system)

Brightness

20,000 lumens (four lamp)

Center-to-corner uniformity

90%

Contrast

10,000:1 (full on/full off, in dynamic iris 3 mode)

Scanning frequency - SDI

Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 372 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 2048 x 1080/24p, 2048/1080/24sF Dual-link HD-SDI signal (X Y Z 4:4:4 12-bit): SMPTE ST 372 compliant: 2048 × 1080/24p, 2048 × 1080/24sF, 3G-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 424 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 3G-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 424 compliant: 1080/50p, 1080/60p, HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 292 compliant: 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE ST 259 compliant: 480i, 576i

Scanning frequency - HDMI/DVI-D/ DIGITAL LINK

Horizontal: 15 –100 kHz, vertical: 24– 120 Hz, dot clock: 25–162 MHz

Scanning frequency - RGB

Horizontal: 15 –100 kHz, vertical: 24– 120 Hz, dot clock: 162 MHz or less

Scanning frequency - YPBPR (YCBCR)

480i (525i): fH 15.73 kHz; fV 59.94 Hz, 576i (625i): fH 15.63 kHz; fV 50 Hz, 480p (525p): fH 31.47 kHz; fV 59.94 Hz, 576p (625p): fH 31.25 kHz; fV 50 Hz, 720 (750)/60p: fH 45.00 kHz; fV 60 Hz, 720 (750)/50p: fH 37.50 kHz; fV 50 Hz, 1035/60i: fH 33.75 kHz; fV 60 Hz, 1080 (1125)/60i: fH 33.75 kHz; fV 60 Hz, 1080 (1125)/50i: fH 28.13 kHz; fV 50 Hz, 1080/25p: fH 28.13 kHz; fV 25 Hz, 1080/24p: fH 27.00 kHz; fV 24 Hz, 1080/24sF: fH 27.00 kHz; fV 48 Hz, 1080/30p: fH 33.75 kHz; fV 30 Hz, 1080/60p: fH 67.50 kHz; fV 60 Hz, 1080/50p: fH 56.25 kHz; fV 50 Hz

Scanning frequency - Video/S-Video

fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60] fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

Optical axis shift - Vertical

±50% (±40% with the ET-D75LE6, +71% with the ET-D75LE90) from center of screen, powered

Optical axis shift - Horizontal

±30% (±20% with the ET-D75LE6) from center of screen, powered

Keystone correction range

Vertical ± 40°, horizontal ± 15° (vertical ±22° and horizontal ±15° with the ET-D75LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6, vertical +5° and horizontal ±15° with the ET-D75LE90)

Keystone correction range when using the optional upgrade kit ET-UK20

Vertical ±45°, horizontal ±40° (vertical ±40° and horizontal ±40° with the ET-D75LE1/2/10/20, vertical ±28° and horizontal ±15° with the ET-D75LE6, vertical ±22° and horizontal ±15° with the ET-D75LE5/50)

Curved correction range

Vertical ±20°, horizontal ±15° (vertical ±8° and horizontal ±8° with the ET-D75LE5/50, vertical ±10° and horizontal ±10° with the ET-D75LE6)

Installation

Ceiling/floor, front/rear

Terminals - SDI IN 1

BNC × 1, Dual-link 3G-SDI signal: SMPTE ST 425 compliant (Link 1)Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A) 3G-SDI signal: SMPTE ST 424 compliant HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant

Terminals - SDI IN 2

BNC × 1, Dual-link 3G-SDI signal: SMPTE ST 425 compliant (Link 2) Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B) 3G-SDI signal: SMPTE ST 424 compliant HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant

Terminals - HDMI IN

HDMI 19-pin × 1, Deep Color, compatible with HDCP

Terminals - DVI-D IN

DVI-D 24-pin × 1, DVI 1.0 compliant, HDCP compatible, for single link only

Terminals - DIGITAL LINK/LAN

RJ-45 Network connection / digital link connection (video/network/serial control) compliant with PJLink (class1) ,100base-tx, Art-Net compatible Deep Color, compatible with HDCP

Terminals - RGB 1 IN

BNC × 5

Terminals - R, G, B

R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Terminals - Y, PB, PR (Y, CB, CR)

Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms

Terminals - S-Video signal

Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

Terminals - RGB 2 IN

D-sub HD 15-pin (female) × 1

Terminals - 3D SYNC 1 IN/OUT

BNC × 1, 1.0 Vp-p, 75 ohms Input: TTL, high impedance. Output: TTL, max. 10 mA

Terminals - 3D SYNC 2 OUT

BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA

Terminals - SERIAL IN

D-sub 9-pin (female) × 1 for external control (RS-232C compliant)

Terminals - SERIAL OUT

D-sub 9-pin (male) × 1 for link control

Terminals - REMOTE 1 IN

M3 jack × 1 for wired remote control

Terminals - REMOTE 1 OUT

M3 jack × 1 for link control

Terminals - REMOTE 2 IN

D-sub 9-pin (female) × 1 for external control (parallel)

Power cord length

3.0 m (9 10 in)

Cabinet materials

Molded plastic

Dimensions (W × H × D)

620 × 291 × 800 mm (24-7/16 × 11-15/32 × 31-1/2 inches) (without lens)

Weight

Approx. 41 kg (90.4 lbs) (without lens)

Operation noise

46 dB (quad lamp operation)

Operating temperature

0°– 45°C (32°–113°F)

Operating humidity

10%–80% (no condensation)

Remote control unit - Power supply

3 V DC (AA/R6 type battery × 2)

Remote control unit - Operation range

Approx. 30 m (98 ft 5 in) when operated from directly in front of the signal receptor

Remote control unit - Dimensions (W × H × D)

47.5 × 181.5 × 27.5 mm (1-7/8 × 7-5/32 × 1-3/32 inches)

Remote control unit - Weight

Approx. 150 g (5.3 oz) (including batteries)

Supplied accessories

Power cord with security lock (× 1), Wireless/wired remote control unit (× 1), Batteries for remote control (AA/R6 type × 2), Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software) (× 1)

Optional accessories

Zoom lens (1.0 –1.2:1) - ET-D75LE6, Zoom lens (1.4– 1.8:1) - ET-D75LE10, Zoom lens (1.8 – 2.6:1) - ET-D75LE20, Zoom lens (2.6 – 5.1:1) - ET-D75LE30, Zoom lens (5.0 – 8.0:1) - ET-D75LE40, Zoom lens (7.9 – 15.0:1) - ET-D75LE8, Fixed-focus lens (0.8:1) - ET-D75LE50, Fixed-focus lens (0.39:1) - ET-D75LE90, Lens motor cover - ET-D75MC1, Ceiling mount bracket - ET-PKD520H (for high ceilings), ET-PKD520S (for low ceilings), Projector mount bracket - ET-PKD520B, Frame - ET-PFD510, Smoke cut Žfilter - ET-SFR510, Upgrade kit - ET-UK20, Auto sreen adjustment upgrade kit - ET-CUK10 (except in the United States), Replacement lamp unit - ET-LAD520 (one bulb), ET-LAD520F (a set of four bulbs), Replacement lamp unit for portrait mode - ET-LAD520P (one bulb), ET-LAD520PF (a set of four bulbs), Replacement Žfilter unit - ET-EMF510