Panasonic PT-RS20K DLP Projector, 1400 x 1050 pixel

Screen Size

1.78 – 25.4 m (70 inch – 1000 inch) With 4:3 Aspect Ratio

Display Type

DLP Chip × 3, DLP Projection System

Model Number

PT-RS20K

Brand

Panasonic

Resolution

1400 x 1050 pixel

Power supply

AC 200V-240V, 7.7A, 50/60HzThe light output will decrease to approximately 1/2 when using the projector with AC 100V to AC 120V [9.6A]

Power consumption

1,510 W (1,525 VA [AC200V]) (0.3 W with Standby Mode set to Eco, 4 W with Standby Mode set to Normal)

Power consumption - Normal Mode

1,217W

Power consumption - Eco Mode

972 W

Power consumption - Operating Temperature

25 °C (77 °F)

Power consumption - Altitude

700m (2,297ft)

Power consumption - IEC627087

2008 Broadcast contents

Power consumption - Picture mode

Standard, Dynamic contrast

BTU value

Max 5,159 BTU

DLP chip - Panel size

24.1 mm (0.95 inches) diagonal (4:3 aspect ratio)

DLP chip - Pixels

4,410,000 (1400 x 1050 x 3) pixels

Refresh rate

120 Hz

Lens

Optional (no lens included with this model), powered zoom, powered focus lens

Light source

Laser Diode (Laser class: Class 1)Class 3R for North America

Illumination life of set

Varies depending on operation mode setting.20,000 hours at half luminance (Normal) 24,000 hours at half luminance (Eco) IEC62087: 2008 Broadcast contents, Dynamic contrast [3] (NORMAL/ECO Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic Contrast [3] Under conditions of 0.15 mg/m3 of particulate matter

Brightness

21,000 lm (Center) / 20,000 lm (Normal)

Center-to-corner uniformity

90 %

Contrast

20,000:1 (Full On/Full Off, Dynamic Contrast Mode: 3)

Scanning frequency - Video/YC

fH:15.73KHz fV:59.94Hz, fH:15.63KHz fV:50Hz

Scanning frequency - RGB

Resolution: 640 x 400 pixels to 1920 x 1200 pixels, Dot clock frequency: 162MHz or less, PIAS (Panasonic Intelligent Auto Scanning)

Scanning frequency - YPBPR(YCBCR)

Resolution: 480i/576i to 1920 x 1080 pixels, Dot clock frequency: 148.5MHz or less, The SYNC/HD and VD terminals do not support 3 value SYNC

Scanning frequency - DVI

Moving image signal resolution: 480i*6/576i*6 to 1920x1080 Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace), Dot clock frequency: 25 MHz to 162 MHz

Scanning frequency - HDMI/DIGITAL LINK

Moving image signal resolution: 480i*6/576i*6 to 1920x1080 Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace) • Dot clock frequency: 25 MHz to 162 MHz

Scanning frequency - SDI

SD-SDI signal, HD-SDI signal, 3G-SDI signal

Optical axis shift

Vertical (from center of screen) ±50 % (±40 % with ET-D75LE6, +67 % – +71 % with ET-D75LE95) (powered), Horizontal (from center of screen) ±30 % (±20 % with ET-D75LE6, ±8 % with ET-D75LE95) (powered)

Installation Terminals

Ceiling/floor, front /rear, free 360-degree installation

Installation Terminals - RGB1 IN

BNC × 5

Installation Terminals - R,G,B

R: 0.7 Vp-p, 75 ohms,G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,B: 0.7 Vp-p, 75 ohmsHD, VD/SYNC: TTL, high impedance, positive/negative automatic

Installation Terminals - Y, PB, PR (Y, CB, CR)

Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms

Installation Terminals - Y/C

Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms

Installation Terminals - VIDEO IN

BNC × 1, 1.0 Vp-p, 75 ohms

Installation Terminals - RGB2 IN

D-sub HD 15-pin (female) × 1

Installation Terminals - DVI-D IN

DVI-D 24-pin ×1 Single link, DVI 1.0 compliant, HDCP compatible

Installation Terminals - HDMI IN

HDMI 19-pin x1HDCP compatible, Deep Color compatible

Installation Terminals - SDI IN 1

BNC × 1SD-SDI signalSMPTE ST 259 compliantHD-SDI signal SMPTE ST 292 compliant3G-SDI signal SMPTE ST 424, 425-2 compliantDual link HD-SDI (LINK A) signal SMPTE ST 372 compliantDual link 3G-SDI (Link 1) signal SMPTE ST 425-3 compliant

Installation Terminals - SDI IN 2

BNC × 1SD-SDI signalSMPTE ST 259 compliantHD-SDI signal SMPTE ST 292 compliant3G-SDI signal SMPTE ST 424, 425-2 compliantDual link HD-SDI (LINK B) signal SMPTE ST 372 compliantDual link 3G-SDI (Link 2) signal SMPTE ST 425-3 compliant

Terminals - DIGITAL LINK

RJ-45HDBaseT compliant, HDCP compatible, Deep Color compatible

Terminals - 3D SYNC1 IN/OUT / MULTI PROJECTOR SYNC IN

BNC × 1, IN : TTL Hi-z OUT : TTL max10mA

Terminals - 3D SYNC2 OUT /MULTI PROJECTOR SYNC OUT

BNC × 1, TTL max10mA

Terminals - SERIAL IN

D-sub 9-pin × 1 for external control (RS-232C compliant)

Terminals - SERIAL OUT

D-sub 9-pin × 1 for link control

Terminals - REMOTE 1 IN

M3 jack × 1 for wired remote control

Terminals - REMOTE 1 OUT

M3 jack × 1 for link control

Terminals - REMOTE 2 IN

D-sub 9-pin × 1 for external control (parallel)

Terminals - DIGITAL LINK/LAN

RJ-45 × 1 for network connection, 100Base-TXPJLink (class 2) compatible, Art-Net compatible

Terminals - DC OUT 5V

USB connector (type A) x 2 for power supply only (DC 5V, Max 2A)

Power cord length

3.0 m(9 ft 10 in)

Cabinet materials

Molded plastic

Dimensions (W × H × D)

598 × 270 × 725 mm (23 17/32 ̋ x 10 5/8 ̋ x 28 17/32 ̋ ) (not including protruding parts)

Weight

Approximately 49kg (108 lbs) (not including lens)

Operation noise

46dB

Operating environment

Operating temperature: 0–50 °C (32–122 °F)10; Operating humidity: 10–80 % (no condensation)

Remote control unit - Power supply

DC 3 V (AAA/R03/LR03 battery × 2)

Remote control unit - Operation range

Approx. 30 m (98 ft 5 in) when operated from directly in front of the signal receptor

Remote control unit - Dimensions (W × H × D)

47.5 x 181.5 x 27.5 mm (1-7/8 in x 7-5/32 in x 1-3/32 in)

Remote control unit - Weight

Approx. 150g (5.3 ozs.) (including batteries)

Supplied accessories

Power cord with secure lock (×2), Wireless/wired remote control unit (×1), Batteries for remote control (AA/R6 type ×2), Lens hole cover (× 1), Lens drop-prevention screw (× 1)

Optional accessories

Zoom lens (1.01–1.19:1) - ET-D75LE6, Zoom lens (1.41–1.81:1) - ET-D75LE10, Zoom lens (1.80–2.61:1) - ET-D75LE20, Zoom lens (2.60–5.05:1) - ET-D75LE30, Zoom lens (5.00–7.99:1) - ET-D75LE40, Zoom lens (7.95–14.9:1) - ET-D75LE8, Fixed-focus lens (0.752:1) - ET-D75LE50, Fixed-focus lens (0.394:1) - ET-D75LE95, Ceiling Mount Bracket (for High ceilings) - ET-PKD520H, Ceiling Mount Bracket (for Low ceilings) - ET-PKD520S, Ceiling Mount Bracket (Projector Mount Bracket) - ET-PKD520B, Stepping Motor kit - ET-D75MKS10, Frame - ET-PFD510, Upgrade kit - ET-UK20, Auto Screen Adjustment Upgrade Kit (PC) - ET-CUK10, Lens Fixed Attachment - ET-PLF10, Digital Interface Box - ET-YFB100G, DIGITAL LINK switcher - ET-YFB200G

Compatible Software

Logo Transfer Software, Smart Projector Control (iOS/android), Early Warning Software (Basic license/3-year license) (ET-SWA100series)