Three Phase Close Delta (In Line) Or Open Delta (Inside Delta)
For Bypass Relay, Fault Relay (Change Over Contacts)
Suitable For Both 3 Phase Squirrel Cage Induction Motor And Slip Ring Motor.
Aux Supply Voltage
230 VAC +/- 10%, 50/60 Hz. Max-10VA
Size In Mm
As Given In Above Model Wise Description
Phase Angle Control (self - Synchronized)
Front Panel Push Button Switches For Start/Stop To Start And Stop The Motor. Reset Push Buttonswitch
415VAC/440VAC @ 50Hz. (690VAC-optional)
0 To 415/440VAC 3 Phase Variable Voltage To Achieve Full Speed In Max. 10-20 Sec.
Adjustable Ramp Up Time For Soft Increase Of Output Voltage.
Motor Protection Against Over Load, Phase Failure And Phase Reversal.
For Adjusting Ramp Or Soft Start Time And Jump Start Voltage Level.
For Power ON, External Fault, Bypass, Over Load Trip, Top Of Ramp.
Screw Mount, Wall Mount
Model Wise Description:
- Suitable for 3 phase AC Induction motor up to 205KW (275HP)
- Semikron make SCR modules (SKKT series)
- Reduces starting current
- Motor connection for both 3 wire close delta (In line)
- and 6 wire open delta (in-side line)
- User settable jump start and soft start / ramp time
- Accepts start and stop command from external potential free contact
- Over load trip facility and built in motor protection
- Contactor bypass output and Fault output
- Easy to install and maintain
|Model||Motor Ratings (HP) @ 440VAC||Motor Ratings (KW) @ 440VAC||Max. Starting Current /Continuous current||Std. Sizes |
(H x W x D) mm
|MSS-006||(1 to 6) HP||(0.75 to 4.5) KW||20A / 6.2A||255 x 170 x 80|
|MSS-010||(7 to 10) HP||(5 to 7.5) KW||32A /10.5A||255 x 170 x 80|
|MSS-015||(11 to 15) HP||(8 to 11) KW||45A /15A||255 x 170 x 80|
|MSS-020||(16 to 20) HP||(12 to 15) KW||55A / 18A||315 x 180 x 240|
|MSS-035||(21 to 35) HP||(16 to 26) KW||75A / 36A||315 x 180 x 240|
|MSS-050||(36 to 50) HP||(27 to 37) KW||110 / 50A||315 x 180 x 240|
|MSS-075||(51 to 75) HP||(38 to 55) KW||150A / 75A||385 x 200 x 240 |
|MSS-110||(76 to 110) HP||(56 to 82) KW||230A / 115A||425 x 285 x280|
|MSS-150||(111 to 150) HP||(83 to 111) KW||310A / 155A||450 x 355 x 355|
|MSS-200||(151 to 200) HP||(112.5 to 147) KW||410A / 205A||450 x 355 x 355|
|MSS-225||(198 to 225) HP||(147.5 to 168) KW||470A / 235A||450 x 355 x 355|
|MSS-275||(226 to 275) HP||(170 to 205) KW||570A / 300A||450 x 355 x 355|
A motor soft starter is a device used with AC electrical motors to temporarily reduce the load and torque in the power train and electric current surge of the motor during start-up. This reduces the mechanical stress on the motor and shaft, as well as the electrodynamic stresses on the attached power cables and electrical distribution network, extending the lifespan of the system.
To gradually accelerate the speed of AC 3 phase induction motor it is required to feed increasing voltage to the motor and such behavior is only possible by connecting SCRs in series with the motor. The SCRs are controlled by MSST-15 firing card to generate the firing pulses giving the effect of soft start. Libratherm offers ready to use motor soft starter MSS-XX for 3 phase induction motor. User has access to set the starting voltage to create the torque and to set the soft start time. For over load trip, the feedback it taken from internal CT to monitor the load current and to generate the trip contact in case of over load condition. Once the motor achieves full RPM, it is not required to pass the current through the SCRs and hence these SCRs can be bypassed using external bypass contactor.Item code: